CTC Union FMC-1000S Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Mise en réseau CTC Union FMC-1000S. CTC Union FMC-1000S User manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - FMC-1000M(S)

USER MANUAL FMC-1000M(S) Gigabit Ethernet OAM/IP Web Smart Media Converter

Page 2

10 Chapter 2 Installation 2.1 Chassis Options Note: The converter can be placed in any FMC series chassis, including the 17 slot CH17, 8 slot CH08 c

Page 3

11 2.2 Electrical Installation With a built-in AC power chassis, AC power is supplied to the chassis through a standard IEC C14 3-prong receptacle,

Page 4

12 Chapter 3 Provisioning 3.1 Web Login 3.1.1 Introduction In an effort to make Networking devices easier to configure, many devices can no

Page 5 - Table of Contents

13 3.1.3 Web Main Page

Page 6 - Chapter 1 Introduction

14 3.1.4 System Information, Network Information The information displayed on this page gives specific device, network information, and port status

Page 7 - 1.3 Product Features

15 3.1.5 System Information, DD Information The DD or DDOM information is read from the MSA compliant SFP module and can be displayed via the web use

Page 8 - 1.5 Management Features

16 3.1.6.1 IP Configuration Use this screen to set the TCP/IP configuration for the local unit. Note, that if you change

Page 9 - 1.6 Panel

17 3.1.6.3 Converter Configuration All of these special functions are explained in Section 3.1.8 of this chapter. Select

Page 10 - Chapter 2 Installation

18 3.1.6.4 Port Configuration This screen is for the configuration of the electrical Ethernet port (TP) and the optical port (FX). The opt

Page 11 - 2.2 Electrical Installation

19 3.1.6.6 RMON Counters The counters have an accumulation of received bytes for each port (UTP, Fiber and Management)

Page 13 - 3.1.3 Web Main Page

20 3.1.6.7 VLAN Group Configuration FMC-1000M(S) supports up to 16 VLAN groups. By using the check boxes for each port, t

Page 14

21 3.1.6.8 VLAN Per Port Configuration In FMC-1000M(S) there are actually three different ports, the external copper and fiber ports, plus

Page 15 - 3.1.6 Local Settings

22 3.1.7 Remote Settings When 802.3ah is active in both the local and remote unit (with fiber connection), the in-band management provides an embedde

Page 16 - 3.1.6.2 Password Setting

23 3.1.8.1 802.3ah Configuration To use the OAM functions, the 802.3ah Functions setting must be enabled. It is not enabled by de

Page 17

24 3.1.8.2 Loop back Test The loop back test is a non-intrusive test which uses OAM packets and will not affect normal transmissions. The num

Page 18 - 3.1.6.5 Q-in-Q Configuration

25 3.1.8.3 802.3ah Status The Global Config fields display the state of OAM, if OAM is enabled. We can also see the MAC

Page 19 - 3.1.6.6 RMON Counters

26 Most information carried by OAMPDU is encoded using type-length-value (TLV) format. The first octet (or byte) of the OAMPDU indicat

Page 20

27 One of the most critical problems in an access network for carriers is differentiating between a simple power failure at

Page 21 - 3.1.6.9 Q in Q Configuration

28 3.1.9.1 System Reboot When the converter is rebooted, all counters and registers are cleared and the converter starts fresh. If OAM is enabled, th

Page 22 - 3.1.8 802.3ah OAM Functions

29 3.1.9.3 Firmware Upgrade If bugs are discovered, if functions are added, or if factory default settings are changed, the firmware in the converter

Page 23

3 CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St., Neihu, Taipei 114, Taiwan T

Page 24 - 3.1.8.2 Loop back Test

30 3.1.10 Logout Logging out will ensure that the management session with FMC-1000M(S) is terminated. This is especially important if you are using a

Page 25 - 3.1.8.3 802.3ah Status

31 3.2.2 LED Observations 3.2.2.1 Power On At initial power on, PWR LED will be lit. Error conditions : If all LEDs immediately light and never tu

Page 26

32 3.2.3.2Ping Test With FMC-1000M(S) reset to factory default, connect a PC and configure the PC to the 10.1.1.0 network (10.1.1.100 recommended).

Page 28 - 3.1.9.2 Save and Restore

4 Legal The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union

Page 29 - 3.1.9.3 Firmware Upgrade

5 Table of Contents CHAPTER 1 INTRODUCTION ...

Page 30 - 3.2 Troubleshooting

6 Chapter 1 Introduction 1.1 Welcome Thank you for choosing FMC-1000M(S) Gigabit Ethernet OAM/IP Web Smart Media Converter. Throughout

Page 31 - 3.2.3.1 Converter Check

7 1.3 Product Features  Auto-Cross over for MDI/MDIX at UTP port  Auto-Negotiation or Forced Manual mode for UTP port  Supports Dual Rate (100

Page 32 - 3.2.3.3 Web Access Test

8 1.4 Specifications  Optical Interface  Connector SFP cage (1000MS) or Duplex SC, ST, FC (1000M)  Data rate 100/1000Base-FX (125Mbps/1.

Page 33

9 1.6 Panel The LAN Speed and FX Speed LEDs use dual color to indicate speed. Green indicates Fast Ethernet (100M). Yellow indicates Gig

Commentaires sur ces manuels

Pas de commentaire