CTC Union SHDTU03 Manuel d'utilisateur Page 7
- Page / 68
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 1. Introduction
1-1
I
I
.
.
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
The SHDSL NTU offers two different ways to connect customers to high-
speed TDM services with two G.703 E1 interfaces (balance 120 Ohm RJ45
jack or unbalance 75 Ohm dual BNCs). The G.703 interface will carry data
at N*64kbps rates (where n=1~32).
The SHDSL NTU can be configured and managed via EOC, or menu-driven
VT100 compatible Asynchronous Terminal Interface, either locally or
remotely.
The SHDSL NTU is equipped with an auto rate capability that identifies the
maximum line rate supported by the copper loop. This powerful automatic
configuration capability makes installation and service provisioning simple
and painless. Further flexibility is provided in the ability to manually set the
maximum NTU speed at different levels for different customer-tailored
service offerings.
? Standard G.shdsl (ITU G.991.2) supports improved reach/speed and
greater interoperability
? Fast and cost-effective provisioning of traditional frame relay (FR or T-
HDLC) or TDM leased line services
? Uses existing copper loop infrastructures
? Can operate in back to back connection
? Efficient single wire pair usage
? Up to 2.312Mbps symmetric service bit rate
? Auto rate installation maximizes data rate based on loop conditions
? Local management interface with LCD display
? Remote line loopback
? SHDSL Line performance monitoring
? Raw and per time interval statistics
? Bandwidth guaranteed transmission equipment
- USER MANUAL 1
- Revision Date Notes 3
- Table of Contents 5
- Chapter 1. Introduction 10
- I. Front Panel 11
- LED Color 12
- Description 12
- Connector Description 13
- I. Wetting Current 15
- I. Purpose 17
- II. How to use key pads 17
- III. Menu Tree 18
- The menu tree is as follows 20
- DIAG LOOPBACK 24
- II. Window Structure 26
- (SMT) 27
- IV. Main Menu Summary 29
- 32
- VI. Configure the SHDSL NTU 33
- Configure SHDSL type 34
- Configure SHDSL parameters 35
- Fractional E1 39
- Unframed E1 40
- Configure EI parameters 40
- Restore factory default 46
- VIII. Reboot the SHDSL NTU 48
- IX. View the System Status 49
- XI. Upgrade the SHDSL NTU 52
- XII. Diagnostic 55
- Loopback Define E1 vs E1 56
- XIII. Exit SMT 58
- Appendix I 61
- 1 8 62
- Top View 62
- Front View 62
- APPENDIX 63
- Appendix III 64
- Transmission Units 68
Produits connexes et manuels pour Mise en réseau CTC Union SHDTU03
Mise en réseau CTC Union SHDSL Spécifications
(110 pages)
(110 pages)
Mise en réseau CTC Union SHDSL Spécifications
(120 pages)
(120 pages)
Mise en réseau CTC Union FMUX-01A Spécifications
(104 pages)
(104 pages)
Sony MDR-EX32LP manuály
Uživatelské manuály a uživatelské příručky pro Sluchátka Sony MDR-EX32LP.
Poskytujeme 2 manuály pdf Sony MDR-EX32LP ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels